Saturday, December 24, 2011

How to setup an Amp

!±8± How to setup an Amp

How to setup an Amplifier:

1.) Disconnect the battery terminals: Just be safe. Do this.

2.) Run the power cable from the battery to the location of the amp or distribution block. (To read more about running wires, click here)

If you run it straight through any sort of sheet metal, be sure to safe the power cable with a rubber grommet, or some other protective device.

Be sure you have fullness of slack at both ends of the cable. This will make your life easier, trust me!

Be sure you run the power cable away from any Rca cables. I ordinarily run the power cable down the side of the car that the battery is installed on, and run the Rca cables down the town of the vehicle.

Once the cable has been run and secured, leave it alone for the time being. Don't hook it up, cut it or do whatever else with it!

Be sure the power cable is secured with wire ties or some other means, But! Not until you have run the cable, and thought about that the cable is going to work out where it is located.

3.) Find a suitable ground point close to the amplifier

This point should attach to the vehicle's chassis, and be a solid connection.

Run your ground cable from the amp (or distro block).

Just like with the power cable, this wire should be secured and protected. It should not be installed in a location that will distress it.

Use a piece of sandpaper to remove any paint or stop from your ground point. Use it to also sand away any rust or residue on your ground point. You want a good solid connection, so you'll want to see nice shiny metal.

Prepare an appropriately sized ring terminal

If your ground cable is going to be attached with a ring concluding (the most recommended means), attach it now. Remember! Do a good job here. We're seeing for a strong, solid electrical connection. If you can use solder, I would advise it!

Use a washer when attaching your ring concluding to your vehicle's chassis.

Finally, cover the ground point with something non-conductive. Also, Find some spray paint or stop that will safe your ground point from rust.

4.) Be sure to run Rca cables and the remote turn on!

Pull your head unit out of its mounting location.

If it's not already hooked up, hook up your remote turn-on wire to the head unit's wiring harness.

Determine which Rca cables will go to each channel on your amp(s). I find it beneficial to have a 4-channel cable and an supplementary 2-channel cable for your subwoofers. This makes it easier to run all of the wires at once.

Run your Rcas and remote turn-on. Keep the Rca cables away from any sort of power cable, especially the power cable for your amp(s). It's Ok to run the remote turn-on wire with the Rcas.

Make sure all cables are secured and not installed in a way that will distress them. Be sure they aren't pinched, scraped or kinked during any sort of driving activity. In any places where they'll need protection, be sure to cover them with a tough material.

5.) Run all of your speaker wires.

Now it's time to run more wires! Run speaker wires from your speakers to your amp's facility location.

Just like with all of the separate wires above, be sure they are secured and protected.

6.) Hook up all of the wires at the amplifier!

Hook up the Rcas, speaker cables, remote turn on, power then ground.

7.) Hook up a fuse possessor near the battery.

Be sure you have this piece of equipment (and a fuse) before you even effort to hook your amp up to your vehicle's electrical system. Seriously!

The fuse possessor Must be within 18" of the battery.

Be sure the fuse possessor is related solidly to the power wire.

Be sure you have the right sized fuse!

Be sure the fuse possessor is mounted in a safe place, and the power wires are all secured away from any entertaining parts.

8.) Hook up any extra battery terminals

If you have any fancy-schmancy battery terminals, now is the time to be sure they're related properly. Be sure they are collect and protected. Hook up any other of your vehicle's cables to the battery. If you can get covers for your new battery terminals, I would advise them.

9.) Reconnect the battery.

Put your shiny new terminals on those battery posts!

10.) Test!

Before turning your system on, turn the amplifier gains all the way down. Turn on your system and listen. Does all things work? How much noise do you hear? Is there audible distortion (If so, don't listen for long!) If everything's square, move on to the next step!

11.) Permanately Mount your amplifier

I hope that before you have gone straight through the former nine steps, you have conception about how your amp fits into your system, and how you plan to setup it. If not, I Beg Of You to think about this first. Form out where you want your amp, how you'll get power to it, and what (if any) components will be installed near it. Also, don't be a fool! Be sure you've budgeted so you can certainly afford all things you need for your amp to be installed Flawlessly. Taking just a small estimate of time to think about this stuff will pay off for a level install, and great sound. If you don't plan, you will screw it up.

When you mount your amp, you'll want to be sure you are protecting it from any sort of corporeal damage and heat. Car amps are tough, but you need to be sure that you are installing it in a way that protects your amp from these hazards.

Soooooo, to safe your amp from corporeal damage (because they are ordinarily installed in places where they are prone to damage such as in the trunk or under the seats), it is best to build some sort of enclosure for it. This enclosure should be big sufficient to comprise the amp (and perhaps some fans), as well as the standard wiring. You will also want to be able to certainly entrance the controls. If you certainly like to tweak your system, you might want to make your amp rack certainly removable, but also keep theft in mind. Be creative on how to safe it. The truth is, you can get certainly fancy here, or just do something quick. Both will work.

Another thing to keep in mind when building an enclosure for an amp or mounting the amp in a place that is hot or has poor airflow is that the amp will get Hot. Heat damages electronics, so you should Form out a way to keep your amp cool and happy. Use fans, or even redirect the air conditioner!

One last thing about amps: I have found that if your amp is mounted to metal, it is sometimes prone to noise. I advise mounting your amp to a piece of wood before installing it. This will preclude any sort or weird ground loop effects that introduce noise to your music.

12.) Tweak!

Now that you've installed your amp(s), you're pretty excited to get rollin. Step 1: Be sure all of the amp's gains are down, the bass boost is off, and the crossovers are set to the spoton frequency band.

Get one of your popular Cds, preferably one that is clean sounding. I have found classical and jazz to work great, but alternative and pop work as well. Try to avoid certainly loud or bass heavy music. If you must, try to use a more melodic Cd: Not one that's just all bass, or noise, you know? The foremost thing is that the Cd is representative of what you ordinarily listen to, because it's Your system, and it's Your music. Darn tootin!

Step 2: Power on!

Step 3: Turn your head units controls to neutral. Eqs off, loudness off, fade and equilibrium centered.

Step 4: Turn the volume up until you hear distortion (you know it when you hear it, and go on to step 5), or the volume control is all the way up. (go to step 6)

Step 5: If you hear distortion, back the volume up until no more distortion is heard. At this point, you know how loud your system is gonna go before it starts distorting, sounding horrible, and smoking speakers. (Move on to step 7, and lower your volume!)

Step 6: If your head unit goes all the way up, and doesn't distort, you have a good unit that your amp can handle. Go to your amp, and while the music is playing, slowly turn up the gains. Once you hear distortion, back off a little. Turn your head unit's volume down!

Step 7: Now go to your head unit. Set all of the eq, loudness, crossover controls, and dsp that you want. Repeat steps 4-6 with all of these controls set to how you want them.

Step 8: Set all of your amp's bass boost or other controls to how you want them. Repeat steps 4-6 again.

Step 9: Once all things sounds good, you're ready to put a cover on your amp enclosure, and be sure your fans are hooked up properly. Put it away and forget it!

Step 10: You're in business! Have fun, and don't wake up your neighbors!


How to setup an Amp

Caulk Tape For Sale Online Price Wire Electrical Supplies Digital Camera Dslr On Sale

No comments:

Post a Comment